Tutorial: A Garden Gathered Autumn Wreath

The hedgerows are full of bejewelled branches and the garden is offering up the most perfect seeds heads, hips and haws. Hydrangeas are ageing beautifully in the colder weather and a glut of Helichrysum appearing in the borders. The perfect ingredients for a garden gathered wreath.

  An Autumn wreath from last year. All materials were fixed to the grape vine wreath using a glue gun. 

 

An Autumn wreath from last year. All materials were fixed to the grape vine wreath using a glue gun. 

I love wreaths and they make the perfect adornment for any front door. I also believe that they should be used all year round and not just limited to the festive season. Autumnal wreaths can take on many forms. Branchy and asymmetrical, hydrangeas bound onto a copper frame or berries and seed heads glued onto a grapevine ring.

Following is a little tutorial for my style of Garden Gathered Wreath. I have gone for a standard shape, laden with Autumnal berries, Rosehips, Heather, dried Hydrangea and Helichrysum from the garden along with Spindle Berry, Hawthorn and wild Clematis as the base foliage. All materials were sourced from the garden or lanes within 100 metres of the house. The only purchase required was the pot of Heather from the local greengrocers.

The materials you will require are as follows:

WREATH BASE:

1 x Copper 12" Wreath Ring (I normally go for the raised form to give better wreath profile)

1 x Bag of Moss - available from local florists or garden centres

1 x reel of Florists wire (stronger than mossing twine)

FLORAL MATERIAL: 

5 x branches of Hawthorn

3 x branches of Spindle Berry

10 x Dried or Fresh Hydrangea Heads

1 x Pot of Erica gracilis or Heather

Assorted Rose hips of various sizes and colours if possible

10 x Helichrysum or Strawflower heads

15 x Heads of Clematis vitalba or 'Old Man's Beard'

Step I: Select/Forage materials

When selecting materials for a wreath, it is always a good idea to go for a range of textures; this gives the final masterpiece more interest. I am constantly looking in the hedgerows for forgeable materials, many of which are overgrown near to the house. Autumn offers the most interesting finds and I always pick up interesting seed heads, dried leaves and fruits to add to wreaths during the winter months. I cannot resist fallen crab apples, hops and 'Old Mans Beard', always taking the opportunity to hoard them in my studio.

Step II: Mossing your wreath ring

Start by attaching you reel wire to the outer ring of the copper frame. Make a sausage shape from your moss and push it onto the wire frame. In a clockwise motion, bind the moss onto the frame making sure the wire is secure and not loose. I would recommend that you have a firm moss base, else the wreath will become too loose. Continue to 'moss up' the whole wreath ring, making sure that you do not cut the wire at any time. Leave the wire attached, to continue adding the foliage.

Step III: Adding your base foliage and wispy bits......

It's always a good idea to cut small bundles of foliage etc, so you can make up the wreath continuously - rather than stopping and snipping. I always create three piles of base foliage. Large branches, for the outer edge of the wreath; Medium for the middle section and Small for the inner section. 

Start by binding your outer section first. I normally use three stems of mixed foliage angled outwards. Once this is bound on, add the middle section of foliage onto the top of the wreath and bind on. Then add the inner section, angling inwards and bind on......continue by adding the next outer section slightly below the previous one and so on. Always work in an anti clockwise motion (very important!) until you covered the whole ring, making sure you cover the mechanics under the last bunches of cut material. 

Make sure the inner branches for the wreath are small, so you can see the centre; else it will look like a mound of foliage.

Step IV: Wiring off

IMG_5677.jpg

Once the base has been finished, the reel wire can be cut and pulled through the copper ring tightly; two or three times to ensure that all materials are bound onto the base. Tuck the end of the wire into the moss at the back of the wreath, so it doesn't scratch you paintwork!

Step V: Wiring and adding additional material and flowers

IMG_5678.jpg

Step VI: Adding the wired materials

Extra green material and flowers can be added to fill any gaps, or to add accents of colour. The easiest way to do this, is by hair pin wiring small branches or florets using florists stub wires (I use a 90 gauge wire) and inserting into the wreath. Some dried material or flower heads can be delicate, so try not to be too rough when handling.

Insert the wired material into the wreath by pushing into the moss at an angle. Pull the wire through the underside and bend the end of the wire back into the moss, this will ensure that the wired material will be securely attached to the wreath. Once all material have been wired on, tie on some ribbon or wire for hanging the wreath. I am not a huge fan of bows on wreaths and prefer the materials to speak for themselves.

Step VII: Hanging in position

IMG_5681.JPG

Once placed in it's desired position it can be misted and enjoyed for at least two or three weeks. Mist every few days to maintain the green material. Once the materials are past their best, the copper ring can be recycled for later use. Make sure all wire is removed before composting the green material. If you are foraging certain material, please do so responsibly.

Lastly, enjoy Autumn..........